Embedded Computing Solutions
The Elma Electronic Systems group includes Embedded Computing Products and Services,
formerly known as ACT/Technico. For all product groups, visit elma.com
Tel.: 215-956-1200 :: Toll free: 800-445-6194 ::
The Elma Electronic Systems group includes Embedded Computing Products and Services,
formerly known as ACT/Technico. For all product groups, visit elma.com
Tel.: 215-956-1200 :: Toll free: 800-445-6194 ::
Adapters/Carriers
- Meets PCI Mezzanine Card (PMC) IEEE 1386 specification
- Compatible with Motorola PowerPC SBCs and others with PMC sites
- Off-the-shelf PMC modules fit a wide variety of applications
- Reduce development costs of implementing PMC technology
- When used with ACT/Technico's CompactPCI-PMC Adapter (7000 series), functionality can be added without concern for form factor compatibility
- Custom designs are readily available
- Devices drivers available: VxWorks, LynxOS, Solaris, Linux, and Windows
2eSST VME to PMC/PMC-X
2eSST VMEbus Carrier for PrPMC and PMC Modules
Model 5000
Model 5000
- Provides a high performance VMEbus interface for two PMC/XMC slots with an increasing of 4x the usable bus bandwidth compared with existing solution
- Standards supported with the VMEbus interface :
- Backward compatible with legacy protocols to preserve the existing VME system
- VME64x extensions
- 2eVME and 2eSST protocols
- Full VMEbus system controller
- Interrupt and Interrupt handling capability
- PMC site one:
- PrPMC or PMC 32/64-bit with PCI 33/66MHz or PCI-X 50/100Mhz
- Compliant with IEEE1386.1
- XMC support via 8-bit parallel RapidIO to the second PMC slot
- VME interface via PCI-X 64-bit bus
- PMC site two:
- PMC 32-bit 33/66MHz or PCI-X up to 100Mhz
- Compliant with IEEE1386.1
- XMC support via RapidIO bus between the two PMCs
- Cyclone FPGA to implement easily specific or customer functions
- LED and Thermal sensor
- 6U-form factor for use in VME or stand-alone systems
PCI to PMC Adapter for Test
Model 8097 * EOL - Please refer to Model 8098 below *
Model 8097 * EOL - Please refer to Model 8098 below *
32/64bit, 33/66MHz PCI-X to PMC-X Adapter
Model 8098
Model 8098
- Permits operation of a standard 32 or 64 bit PCI-X card in a PMC slot
- Passive adapter - no software set up required
- Supports "PCI-X Capable" signal allowing use of legacy PCI boards or PCI-X boards
- LEDs monitor power supplies and key signals from the PCI bus
32/64b 33/66 MHz PCI-x to PMC-x Adapter
Model 8098a
Model 8098a
- Permits operation of a standard 32 or 64 bit PCI-X card in a PMC slot
- Passive adapter - no software set up required
- Supports "PCI-X Capable" signal allowing use of legacy PCI boards or PCI-X boards
- LEDs monitor power supplies and key signals from the PCI bus
- 10 Watt 5V to 3.3V DC to DC converter
PCMCIA to PMC Adapter
Model 8073
Model 8073
- Permits use of a Type I or Type II PCMCIA card in PMC slot
Cardbus/PCMCIA to PMC Adapter
Model 8059
Model 8059
- Permits use of Cardbus and PCMCIA cards in a PMC slot
PMC to 3U CompactPCI Carrier
Model 7000
Model 7000
- 3U CompactPCI Form Factor (100mm high x 160mm deep)
- Only one slot (3U x 4HP) required
- Passive Series Termination
- For use with 32-bit PMCs
- 64 User I/O lines routed to CPCI connector (models 7000-2 and 7000-4)
- 2 Status LEDs: IRQ Request from PMC and PMC Bus Master
- Accepts standard PMC I/O connector through the CPCI front panel
- P/N 7000-1: for use in 64-bit systems; no rear I/O; J1 only
- P/N 7000-2: for use in 32-bit systems; rear I/O; J2 connector
- P/N 7000-3: same as -1, mounted at bottom of 6U Front Panel
- P/N 7000-4: same as -2, mounted at bottom of 6U Front Panel
- Hot Swap version also available - contact sales
PMC to 6U CompactPCI Carrier
Model PMC-202
Model PMC-202
- 6U CompactPCI form factor requires only 1 slot (4 HP)
- Support for 2 single width modules or one dual width module
- 5 Volt or 3.3 Volt signaling
- 32/64-bit and 33/66 MHz PCI interface
- Supports non-Monarch Processor PMC modules
- I/O via front panel and rear via J3 and J4 or J3 and J5 to a Transition Module
- PMC rear I/O routed as differential pairs to support SCSI rear I/O
- Hot swap live insertion support per PICMG 2.1, Rev. 2.0
- PLX Technology PCI 6254 PCI to PCI bridge
- Front panel LED for PCI bus activity
- Extended temperature version also available (-20° C to +70°C)
- RoHS (leaded) and non-RoHS (unleaded) versions available
